Yibin Cuiping Exploration Drilling Rig manufacturers are welcome to prepare the market price before use: small water well drilling rigs, all parts of small water well drilling rig manufacturers, whether the installation is stable and reliable, whether the wire ropes and connections are intact, and remove dust, dirt and other things on the rig. The design brand Yibin Cuiping should pay attention to whether the sound of the impactor and the operation of the machine are normal. If abnormal phenomena are found, it should immediately stop. Customers should also pay special attention to the location of the rig, which should be parked in a dry indoor environment. Due to limited conditions, most water well rigs are parked outdoors. At this time, it should not be placed for a long time in an environment such as saline, dusty, and so on. The customer must ensure that the oil mister is oily and the oil circuit is unobstructed before operating on the Qianjiang River. It is not allowed to work without oil. Details Loosen diesel clutch, water well rig, mud pump clutch, empty car driver, V-type handwheel, observe gearbox, water well rig purchase, main and auxiliary winch cardan shaft, how much is the water well rig, whether the turntable is dead or bite, If any, it should be adjusted. Yibin Cuiping Exploration Drilling Rig is a good manufacturer. The market price welcomes you. In order to adapt to the needs of drilling in different formations and improve drilling efficiency, water well drilling rigs are developing in the direction of multi-purpose drilling rigs and full hydraulic transmission and manipulation: that is, the rig is equipped with a variety of equipment. And attachments, various drilling methods such as impact, rotary and down-the-hole hammers can be used; mud washing, compressed air washing, and positive and reverse circulation washing can also be used . Application process Fill the required parts with oil or grease. In order to ensure the planetary gear bearings of the slewing gear of the slewing gear, the gearbox oil return port on the slewing gear cover should go to the tank hydraulic oil before the first use. The oil level should be the same as the oil return port. Are the same height. Inspection environment
Yibin Cuiping Exploration Drilling Rig Manufacturers at the market price welcome you to inject the casing during the cement construction process to a predetermined depth → install the cement head, circulating mud, ground surface pipeline → hit isolation fluid → inject cement → top rubber plug → replace the mud → bump pressure → The cement injection is finished and waiting to set. When the cylinder liner and the new product are installed without replacement, the cylinder liner and the new product are considered as standard parts and are interchangeable, so they can be used after being installed. In fact, Yibin Cuiping exploration rig is a good manufacturer, and the size of the cylinder liner has a certain tolerance range. If a large-sized cylinder liner is fitted with a small-sized one, the fit clearance will be too large, resulting in weak compression and difficult starting. Therefore, the size group code of the standard cylinder liner and the size group code of the cylinder liner must be the same when changing the equipment. Only in this way can the standard cooperation between the two be guaranteed. gap. In addition, when the cylinders are equipped with cylinder liners of the same grouping code, pay attention to the inspection of the cylinder plug clearance before installation. In order to ensure the assembly standard, a test should be performed before installation to prevent fake and inferior products from being installed. In any case, when someone is working on the upper section of the mast, no other personnel are allowed to stay under the mast. How to choose a drill bit for different rock formations is an important drilling tool for water well drilling. It can be said that without a drill bit, the water well rig equipment cannot be started normally, which shows the importance of the drill bit in the water well rig. For different types of water well rig equipment, different drill bits need to be matched in good times. When selecting a water well rig equipment, we should pay attention to the following aspects: When the soft rock with good drillability is good, the speed of research Faster, you need to choose a larger amount of slag discharge and higher slag discharge quality. Fortunately, the wing shape is selected. When the Yibin Cuiping has confirmed that the alloy piece is lost, the drill can be lifted to blow out the alloy block by blowing. When it cannot be blown out, it can also be taken by treating the broken wings of the drill bit, such as a fault or a fracture zone in the hole. At this time, the alloy is squeezed into the hole walls in these places, or it can be left without a new drill bit to continue drilling. There is a serious attitude to do the impact drilling rig rely on the vertical reciprocating movement of the drilling tool to make the drill bit impact the bottom of the well to break the rock formation. Its structure is simple. There is no circulating well washing system. The removal of cuttings and drilling rig cannot be performed at the same time, so the efficiency is low. The drilling depth is generally within 250 meters, sometimes up to 500-600 meters. There are two main types: punching and grasping cones. The weight of the drill itself impacts the formation. At the lower end of the drilling tool are several sharp-angled grasping flaps that can be stretched. When the drilling tool moves downward under its own weight, the flaps are grasped, cut into the rock formation, and then the drilling tool is lifted by the hoist wire rope. The cuttings grabbed the cone and raised the wellhead to unload the cuttings. The drilling depth is usually 40-50 meters and the depth is 100-150 meters. Precautions for the use and maintenance of the drilling rig during the running-in period After leaving the drilling rig, a running-in period of about 60 hours (sometimes called the running-in period) is generally stipulated. This is stipulated by the factory according to the technical characteristics of the initial stage of the engineering rig. The running-in period is an important part to ensure the normal operation of the engineering rig, reduce the failure rate and extend its service life. However, at present, some users ignore the special technical requirements of the running-in period of the new machine due to lack of common knowledge on the use of engineering rigs or because of tight construction schedules, or to obtain benefits as soon as possible. Some users even think that, anyway, there is a repair period, and the machine is broken. The machine will be responsible for maintenance. Therefore, the machine will be overloaded for a long time during the running-in period, which will cause frequent early failure of the machine. The service life of the machine, but also because the machine is damaged, affects the progress of the project. Therefore, attention should be paid to the use and maintenance of the engineering drill during the break-in period. Analysis of Haixi reduction gearbox is mixed with calcium-based grease engine oil, and it is advisable to add additives regularly, and the agent occupies 1 / 3-2 / 3 of the gap in the tank body to ensure the reduction gearbox. Yibin Cuiping Exploration Drilling Rig Manufacturers at the market price welcome you to see if the steel has strong cracks, rust, desoldering, etc. The product line regularly cleans the impactor, wind motor with diesel oil, and observes the damage of the motor blades. good quality
Yibin Cuiping Exploration Drilling Rig is a good manufacturer. The market price welcomes you. All-hydraulic operated drill is also called full hydraulic drilling rig. A drilling rig driven by oil pressure and all moving parts. This type of drilling rig uses the high-pressure variable oil pump to achieve stepless speed change, which can simplify the transmission and eliminate the gear transmission, which not only reduces the weight of the rig, but also has sufficient power. At the same time, the speed of the drilling rig is high, the work is stable, the operation is convenient and safe, and it is easy to realize automation and instrumentation. It is especially suitable for high-speed drilling (such as diamond drilling). However, the processing of the hydraulic components of this rig is more complicated, and the requirements for use and maintenance are relatively high.  From the perspective of structure, all-hydraulic drilling rigs can be divided into two categories: vertical-shaft full-hydraulic drilling rigs; and power-head full-hydraulic drilling rigs. Customer First Summary: Engineering rigs are an indispensable device in our infrastructure construction. With the continuous development of technology, the scope of use of rigs is also increasing, bringing a lot of convenience to our daily lives. Learn how to maintain and Maintenance engineering rig is urgent! Use and maintenance during the break-in period of the agent. As construction machinery is a special vehicle, operators should receive good training and guidance, have a thorough understanding of the structure and performance of the machine, and obtain certain operating and maintenance experience before operating the machine. A good product use and maintenance manual is an essential information for the operator to operate the equipment. Before operating the machine, you must first read the maintenance manual and perform operations and maintenance according to the requirements of the manual. For the open gas, the electricity or oil of the Yibin Cuiping exploration rig is still sealed with the water pipe, and the interior of the channel and joints are kept clean to prevent foreign matter from entering. A kind of rotary drill with hydraulic power head drill. It is driven by a hydraulic motor reducer and replaces the rotary table and faucet on the rotary table rig with a power head that moves up and down the tower to drive the drill rod and drill bit to rotate and cut the rock formation. Large-diameter water wells can be drilled with large drill bits up to 1 meter in diameter, which is characterized by fast drilling speed, simple loading and unloading of drilling tools and downhole pipes, and no need to raise drilling tools when lengthening the drill pipe. , The series of components such as hoisting machine, hoisting pulley, turntable, faucet, square drill pipe are eliminated. Inspection results The failure of the drill rod or the drill bit shall be caused by the failure of the drill rod or the drill bit due to the operation and common walking, which will cause the engineering drill to fail to operate normally. The solution is to replace it. When placed away or stored for long periods of time, it is protected from rain, moisture, stains, ready to be packed, and ready to be packed and packed.